In the Garden:
Pacific Northwest
June, 2012
Regional Report

Share |

This hydrangea is my most prolific, yielding dozens of offspring over the past few years.

Easy Plant Propagation

I have to admit that I accidentally stumbled upon one of the easiest methods of plant propagation you can imagine. A couple of years ago I was cleaning leaves away from the base of my favorite hydrangea, and I discovered that a low-growing branch had rooted where it touched the ground, producing a new little plant. I snipped the stem between mother and baby and later transplanted the offspring into another spot in the garden. I've always known that some plants propagate themselves in this manner, but I'd never actually seen it before. I was struck by how easy it was -- no horticultural skills required.

This experience was my introduction to layering, a natural method of propagation. Since my first discovery I've propagated dozens of plants in this same way. Instead of waiting for an accident of nature, you can create new plants by pinning a branch to the soil, which encourages it to grow roots and form a new plant. It's a simple procedure that takes growing time but not much effort.

Nature Does All The Work
One advantage of layering is its high success rate. Because the branch is still attached to the mother plant and gets water and nutrients from her, there is less chance of the branch tip wilting. Another advantage is space; the new plants grow beneath or beside an existing plant, so they won't need a separate nursery bed for their first year.

Plants that grow easily from cuttings are also the best candidates for successful layering. In general, these are plants that readily put out roots. Besides hydrangeas, likely plants include lilac, viburnum, deutzia, euonymus, honeysuckle, mockorange, spirea, weigela, wisteria, and bramble fruits such as raspberries and blackberries.

Steps to Success
You can try layering any time during the growing season, as long as branches are still green and pliable. Early spring to midsummer provide the best results in my garden. Here are the steps:

First, select a branch that is long enough and supple enough to be bent to the ground without breaking. A branch formed in the current season is most likely to root quickly. You will be rooting it 8 to 12 inches from its tip, so find where that point on the branch will touch the ground, and loosen the soil for the new plant at that spot.

Once you've chosen a likely branch, remove a narrow ring of bark (this procedure is called girdling) or make a small diagonal cut in the bottom side of the branch at the point where it will make contact with the ground. Strip the leaves from the branch in the area of the wound. Then dust that part of the branch with rooting hormone, and prop the cut open slightly with a toothpick or small pebble. Pin the cut or girdled area to the soil, holding it down with a forked stick, a rock or a loop of heavy wire, such as a piece of coat hanger. Arrange the branch so that the growing tip is pointing up, and mound soil over the cut portion. You can even place a stake in the soil and tie the branch tip upright to help support it.

After covering with soil, pile a generous mulch of compost or shredded leaves where the branch is pinned. The mulch helps keep the soil moist while roots form. If the soil dries out, the newly developing roots can be destroyed before they really start growing, so mulching is an important step. Sprinkle the mound with water initially and whenever there are summer dry spells.

The following spring, when the new plant is well-rooted, sever it from the mother plant. At this point the baby still needs extra attention, such as mulch and water, so it's fine to leave it in the ground to get better established for a few weeks or even a year before moving it to a permanent place in the landscape. I usually wait until the following spring to transplant the young plants, but early fall is a good time in warmer climates. Feel free to cut it back before or after transplanting to give it a bushier or more symmetrical form.

In the case of vines, such as honeysuckle or wisteria, it's possible to create several plants by repeating the wounding and burying process along the length of a single long branch -- a technique called serpentine layering. You simply wound the long stems at intervals and peg them into the prepared ground at each interval in the same way as the normal layering technique. Loop the stem up between each pegging. In the case of thorny bramble fruits such as raspberries and blackberries, the branch is more likely to root from the tip, so bury the end of the stem instead of a point along its length. You don't even need to cut or girdle it to stimulate root formation.

Although the plants most likely to grow from layering are not the most expensive to buy, it's still nice after your initial purchase of a favorite cultivar to be able to acquire more in exchange for a little time and no cash. If you need a lot of new shrubs at once, for a long row of raspberries or a viburnum hedge, it's possible to tug many branches out from a single plant, spoke-fashion, and pin them down in a wide circle all around the parent. If you want just one new plant, I'd pin down two and hope for a 50 percent success rate. If all goes well, you'll have an extra plant to give to a friend.

Care to share your gardening thoughts, insights, triumphs, or disappointments with your fellow gardening enthusiasts? Join the lively discussions on our FaceBook page and receive free daily tips!

Our Mission in Action

Shop Our Holiday Catalog